Channel-conveyance capacity, channel change, and sediment transport in the lower Puyallup, White, and Carbon Rivers, western Washington

Channel-conveyance capacity, channel change, and sediment transport in the lower Puyallup, White, and Carbon Rivers, western Washington PDF

Author: Jonathan A. Czuba

Publisher: U.S. Department of the Interior, U.S. Geological Survey

Published: 2010-12-01

Total Pages: 120

ISBN-13:

DOWNLOAD EBOOK →

Draining the volcanic, glaciated terrain of Mount Rainier, Washington, the Puyallup, White, and Carbon Rivers convey copious volumes of water and sediment down to Commencement Bay in Puget Sound. Recent flooding in the lowland river system has renewed interest in understanding sediment transport and its effects on flow conveyance throughout the lower drainage basin. Bathymetric and topographic data for 156 cross sections were surveyed in the lower Puyallup River system by the U.S. Geological Survey (USGS) and were compared with similar datasets collected in 1984. Regions of significant aggradation were measured along the Puyallup and White Rivers. Between 1984 and 2009, aggradation totals as measured by changes in average channel elevation were as much as 7.5, 6.5, and 2 feet on the Puyallup, White, and Carbon Rivers, respectively. These aggrading river sections correlated with decreasing slopes in riverbeds where the rivers exit relatively confined sections in the upper drainage and enter the relatively unconstricted valleys of the low-gradient Puget Lowland. Measured grain-size distributions from each riverbed showed a progressive fining downstream. Analysis of stage-discharge relations at streamflow-gaging stations along rivers draining Mount Rainier demonstrated the dynamic nature of channel morphology on river courses influenced by glaciated, volcanic terrain. The greatest rates of aggradation since the 1980s were in the Nisqually River near National (5.0 inches per year) and the White River near Auburn (1.8 inches per year). Less pronounced aggradation was measured on the Puyallup River and the White River just downstream of Mud Mountain Dam. The largest measured rate of incision was measured in the Cowlitz River at Packwood (5.0 inches per year). Channel-conveyance capacity estimated using a one-dimensional hydraulic model decreased in some river reaches since 1984. The reach exhibiting the largest decrease (about 20–50 percent) in channel-conveyance capacity was the White River between R Street Bridge and the Lake Tapps return, a reach affected by recent flooding. Conveyance capacity also decreased in sections of the Puyallup River. Conveyance capacity was mostly unchanged along other study reaches. Bedload transport was simulated throughout the entire river network and consistent with other observations and analyses, the hydraulic model showed that the upper Puyallup and White Rivers tended to accumulate sediment. Accuracy of the bedload-transport modeling, however, was limited due to a scarcity of sediment-transport data sets from the Puyallup system, mantling of sand over cobbles in the lower Puyallup and White Rivers, and overall uncertainty in modeling sediment transport in gravel-bedded rivers. Consequently, the output results from the model were treated as more qualitative in value, useful in comparing geomorphic trends within different river reaches, but not accurate in producing precise predictions of mass of sediment moved or deposited. The hydraulic model and the bedload-transport component were useful for analyzing proposed river-management options, if surveyed cross sections adequately represented the river-management site and proposed management options. The hydraulic model showed that setback levees would provide greater flood protection than gravel-bar scalping after the initial project construction and for some time thereafter, although the model was not accurate enough to quantify the length of time of the flood protection. The greatest hydraulic benefit from setback levees would be a substantial increase in the effective channel-conveyance area. By widening the distance between levees, the new floodplain would accommodate larger increases in discharge with relatively small incremental increases in stage. Model simulation results indicate that the hydraulic benefit from a setback levee also would be long-lived and would effectively compensate for increased deposition within the setback reach from increased channel-conveyance capacity. In contrast, the benefit from gravel-bar scalping would be limited by the volume of material that could be removed and the underlying hydraulics in the river section that would be mostly unaffected by scalping. Finally, the study formulated an explanation of the flooding that affected Pacific, Washington, in January 2009. Reduction in channel-conveyance capacity of about 25 percent at the White River near Auburn streamflow-gaging station between November 2008 and January 2009 was caused by rapid accumulation of coarse-grained sediment just downstream of the gage, continuing an ongoing trend of aggradation that has been documented repeatedly.

Changes in sediment volume in Alder Lake, Nisqually River Basin, Washington, 1945–2011

Changes in sediment volume in Alder Lake, Nisqually River Basin, Washington, 1945–2011 PDF

Author: Jonathan A. Czuba

Publisher: U.S. Department of the Interior, U.S. Geological Survey

Published: 2012-04-24

Total Pages: 40

ISBN-13:

DOWNLOAD EBOOK →

The Nisqually River drains the southwest slopes of Mount Rainier, a glaciated stratovolcano in the Cascade Range of western Washington. The Nisqually River was impounded behind Alder Dam when the dam was completed in 1945 and formed Alder Lake. This report quantifies the volume of sediment deposited by the Nisqually and Little Nisqually Rivers in their respective deltas in Alder Lake since 1945. Four digital elevation surfaces were generated from historical contour maps from 1945, 1956, and 1985, and a bathymetric survey from 2011. These surfaces were used to compute changes in sediment volume since 1945. Estimates of the volume of sediment deposited in Alder Lake between 1945 and 2011 were focused in three areas: (1) the Nisqually River delta, (2) the main body of Alder Lake, along a 40-meter wide corridor of the pre-dam Nisqually River, and (3) the Little Nisqually River delta. In each of these areas the net deposition over the 66-year period was 42,000,000 ± 4,000,000 cubic meters (m3), 2,000,000 ± 600,000 m3, and 310,000 ± 110,000 m3, respectively. These volumes correspond to annual rates of accumulation of 630,000 ± 60,000 m3/yr, 33,000 ± 9,000 m3/yr, and 4,700 ± 1,600 m3/yr, respectively. The annual sediment yield of the Nisqually (1,100 ± 100 cubic meters per year per square kilometer [(m3/yr)/km2]) and Little Nisqually River basins [70 ± 24 (m3/yr)/km2] provides insight into the yield of two basins with different land cover and geomorphic processes. These estimates suggest that a basin draining a glaciated stratovolcano yields approximately 15 times more sediment than a basin draining forested uplands in the Cascade Range. Given the cumulative net change in sediment volume in the Nisqually River delta in Alder Lake, the total capacity of Alder Lake since 1945 decreased about 3 percent by 1956, 8 percent by 1985, and 15 percent by 2011.

Geomorphic analysis of the river response to sedimentation downstream of Mount Rainier, Washington

Geomorphic analysis of the river response to sedimentation downstream of Mount Rainier, Washington PDF

Author: Jonathan A. Czuba

Publisher: U.S. Department of the Interior, U.S. Geological Survey

Published: 2012-12-07

Total Pages: 150

ISBN-13:

DOWNLOAD EBOOK →

A study of the geomorphology of rivers draining Mount Rainier, Washington, was completed to identify sources of sediment to the river network; to identify important processes in the sediment delivery system; to assess current sediment loads in rivers draining Mount Rainier; to evaluate if there were trends in streamflow or sediment load since the early 20th century; and to assess how rates of sedimentation might continue into the future using published climate-change scenarios. Rivers draining Mount Rainier carry heavy sediment loads sourced primarily from the volcano that cause acute aggradation in deposition reaches as far away as the Puget Lowland. Calculated yields ranged from 2,000 tonnes per square kilometer per year [(tonnes/km2)/yr] on the upper Nisqually River to 350 (tonnes/km2)/yr on the lower Puyallup River, notably larger than sediment yields of 50–200 (tonnes/km2)/yr typical for other Cascade Range rivers. These rivers can be assumed to be in a general state of sediment surplus. As a result, future aggradation rates will be largely influenced by the underlying hydrology carrying sediment downstream. The active-channel width of rivers directly draining Mount Rainier in 2009, used as a proxy for sediment released from Mount Rainier, changed little between 1965 and 1994 reflecting a climatic period that was relatively quiet hydrogeomorphically. From 1994 to 2009, a marked increase in geomorphic disturbance caused the active channels in many river reaches to widen. Comparing active-channel widths of glacier-draining rivers in 2009 to the distance of glacier retreat between 1913 and 1994 showed no correlation, suggesting that geomorphic disturbance in river reaches directly downstream of glaciers is not strongly governed by the degree of glacial retreat. In contrast, there was a correlation between active-channel width and the percentage of superglacier debris mantling the glacier, as measured in 1971. A conceptual model of sediment delivery processes from the mountain indicates that rockfalls, glaciers, debris flows, and main-stem flooding act sequentially to deliver sediment from Mount Rainier to river reaches in the Puget Lowland over decadal time scales. Greater-than-normal runoff was associated with cool phases of the Pacific Decadal Oscillation. Streamflow-gaging station data from four unregulated rivers directly draining Mount Rainier indicated no statistically significant trends of increasing peak flows over the course of the 20th century. The total sediment load of the upper Nisqually River from 1945 to 2011 was determined to be 1,200,000±180,000 tonnes/yr. The suspended-sediment load in the lower Puyallup River at Puyallup, Washington, was 860,000±300,000 tonnes/yr between 1978 and 1994, but the long-term load for the Puyallup River likely is about 1,000,000±400,000 tonnes/yr. Using a coarse-resolution bedload transport relation, the long-term average bedload was estimated to be about 30,000 tonnes/yr in the lower White River near Auburn, Washington, which was four times greater than bedload in the Puyallup River and an order of magnitude greater than bedload in the Carbon River. Analyses indicate a general increase in the sediment loads in Mount Rainier rivers in the 1990s and 2000s relative to the time period from the 1960s to 1980s. Data are insufficient, however, to determine definitively if post-1990 increases in sediment production and transport from Mount Rainier represent a statistically significant increase relative to sediment-load values typical from Mount Rainier during the entire 20th century. One-dimensional river-hydraulic and sediment-transport models simulated the entrainment, transport, attrition, and deposition of bed material. Simulations showed that bed-material loads were largest for the Nisqually River and smallest for the Carbon River. The models were used to simulate how increases in sediment supply to rivers transport through the river systems and affect lowland reaches. For each simulation, the input sediment pulse evolved through a combination of translation, dispersion, and attrition as it moved downstream. The characteristic transport times for the median sediment-size pulse to arrive downstream for the Nisqually, Carbon, Puyallup, and White Rivers were approximately 70, 300, 80, and 60 years, respectively.

Sediment Transport Data and Related Information for Selected Coarse-bed Streams and Rivers in Idaho

Sediment Transport Data and Related Information for Selected Coarse-bed Streams and Rivers in Idaho PDF

Author:

Publisher:

Published: 2004

Total Pages: 32

ISBN-13:

DOWNLOAD EBOOK →

This report and associated web site files provide sediment transport and related data for coarse-bed streams and rivers to potential users. Information on bedload and suspended sediment transport, streamflow, channel geometry, channel bed material, floodplain material, and large particle transport is provided for 33 study reaches in Idaho that represent a wide range of drainage areas, average annual streamflows, channel gradients, and substrate sizes. All the study reaches have a coarser layer of surface bed material overlaying finer subsurface material. Both bedload and suspended sediment transport increase with discharge and the relationship can be reasonably represented using a log-log model. At most sites, the suspended load makes up the majority of the total sediment load. The size of the largest bedload particle in transport and usually the median size of the bedload increase with discharge. However, the median size of the bedload is much smaller than the channel surface material and sand is the primary or a large component of the bedload material. A large proportion of the annual sediment production occurs at the higher streamflows during snowmelt. On average, discharges equal to or larger than bankfull occur 3.3 percent of the time and transport 61.5 percent of the annual bedload sediment. Discharges less than the average annual discharge, on average, occur 75.0 percent of the time and transport about 3.8 percent of the annual bedload sediment.

Channel Change and Bed-material Transport in the Lower Chetco River, Oregon

Channel Change and Bed-material Transport in the Lower Chetco River, Oregon PDF

Author:

Publisher:

Published: 2012

Total Pages: 68

ISBN-13:

DOWNLOAD EBOOK →

The lower Chetco River is a wandering gravel-bed river flanked by abundant and large gravel bars formed of coarse bed-material sediment. Since the early twentieth century, the large gravel bars have been a source of commercial aggregate for which ongoing permitting and aquatic habitat concerns have motivated this assessment of historical channel change and sediment transport rates. Analysis of historical channel change and bed-material transport rates for the lower 18 kilometers shows that the upper reaches of the study area are primarily transport zones, with bar positions fixed by valley geometry and active bars mainly providing transient storage of bed material. Downstream reaches, especially near the confluence of the North Fork Chetco River, are zones of active sedimentation and channel migration. Multiple analyses, supported by direct measurements of bedload during winter 2008-09, indicate that since 1970 the mean annual flux of bed material into the study reach has been about 40,000-100,000 cubic meters per year. Downstream tributary input of bed-material sediment, probably averaging 5-30 percent of the influx coming into the study reach from upstream, is approximately balanced by bed-material attrition by abrasion. Probably little bed material leaves the lower river under natural conditions, with most net influx historically accumulating in wider and more dynamic reaches, especially near the North Fork Chetco River confluence, 8 kilometers upstream from the Pacific Ocean. The year-to-year flux, however, varies tremendously. Some years may have less than 3,000 cubic meters of bed material entering the study area; by contrast, some high-flow years, such as 1982 and 1997, likely have more than 150,000 cubic meters entering the reach. For comparison, the estimated annual volume of gravel extracted from the lower Chetco River for commercial aggregate during 2000-2008 has ranged from 32,000 to 90,000 cubic meters and averaged about 59,000 cubic meters per year. Mined volumes probably exceeded 140,000 cubic meters per year for several years in the late 1970s. Repeat surveys and map analyses indicate a reduction in bar area and sinuosity between 1939 and 2008, chiefly in the period 1965-95. Repeat topographic and bathymetric surveys show channel incision for substantial portions of the study reach, with local areas of bed lowering by as much as 2 meters. A specific gage analysis at the upstream end of the study reach indicates that incision and narrowing followed aggradation culminating in the late 1970s. These observations are all consistent with a reduction of sediment supply relative to transport capacity since channel surveys in the late 1970s, probably owing to a combination of (1) bed sediment removal and (2) transient river adjustments to large sediment volumes brought by floods such as those in 1964 and, to a lesser extent, 1996.

Sediment Transport Dynamics in the Lower Mississippi River

Sediment Transport Dynamics in the Lower Mississippi River PDF

Author: Jeffrey Albert Nittrouer

Publisher:

Published: 2010

Total Pages: 0

ISBN-13:

DOWNLOAD EBOOK →

This dissertation examines the dynamics of sediment transport and channel morphology in the lower Mississippi River. The area of research includes the portion of the river where reach-averaged downstream flow velocity responds to the boundary condition imposed by the relatively uniform water-surface elevation of the receiving basin. Observational studies provided data that are used to identify channel-bed sediment composition, and measure bed-material sediment flux and the properties of the fluid-flow field over a variety of water-discharge conditions. The analyses demonstrate that a significant portion of the channel bed of the final 165 kilometers of the Mississippi River consists of exposed and eroding underlying relict sedimentary strata that qualify as surrogate bedrock. The exposed bedrock is confined to the channel thalweg, particularly in river-bend segments, and actively mobile bed-material sediments are positioned on subaqueous bars fixed by river planform. The analyses for sediment flux provides insight to the nature of sediment transport: during low- and moderate-water discharge, bed-material movement occurs primarily as minimal bedform flux, and so bed materials are not transferred between alluvial bars. During high-water discharge, bed-material transport increases one-hundred fold, and sands move as a part of both suspended and bedform transport. Physical models are used to show that skin-friction shear stress increases by a factor of ten for the measured water-discharge range. This change is not possible given conditions of uniform water flow, and therefore non-uniform flow in response to the Mississippi River approaching its outlet has a significant impact on the timing and magnitude of sediment flux through the lower river. In order to estimate the dynamics of bed material movement from the uniform to non-uniform segment of the river (lower 800 km), data for channel morphology are used to construct a model that predicts spatial changes in water-flow velocity and bed-material flux over a range of water-discharge conditions. The model demonstrates that non-uniform flow tends to produce a region of net channel-bed aggradation between 200-700 kilometers above the outlet, and a region of channel-bed degradation for the final 200. The implication for these results for the spatial variability of channel morphology and kinematics is explored.